Firmware Version Up

 R300

 Firmware　Program >>

 2.1B NEW

 G120
 G100

 Firmware Program >>

 2.3A

 H2640

 Firmware Program >>

 1.0B

 F30W
 F30S

 Firmware Program >>

 2.0

 TH9260

 Firmware Program >>

 1.0M

 TH9100MR
 TH9100WR

 Firmware Program >>

 5.9H

 TH9100MRI
 TH9100WRI

 Firmware Program >>

 I5.9H

 TH9100PMV
 TH9100PWV

 Firmware Program >>

 5.9H

 TH9100PMVI
 TH9100PWVI

 Firmware Program >>

 I5.9H

 TH9100MV
 TH9100WV

 Firmware Program >>

 5.6A

 TH9100MVI
 TH9100WVI

 Firmware Program >>

 I5.6A

 TH9100ML
 TH9100WL

 Firmware Program >>

 I5.6A

 TH9100MLN
 TH9100WLN

 Firmware Program >>

 5.6A

 TH9100SL

 Firmware Program >>

 I5.6A

 TH7800

 Firmware Program >>

 I3.6C

 TH7700

 Firmware Program >>

 I3.6C

 TH7800N

 Firmware Program >>

 3.6C

 TH7716

 Firmware Program >>

 I2.0A

 TH7102MV
 TH7102WV

 Firmware Program >>

 4.2J

 TH7102MX
 TH7102WX

 Firmware Program >>

 3.5G

 TH9260
 TH9100 Series
 TH7100 Series
 TS9100 Series
 TS7302

 IEEE1394 Driver Program >>

1.0.6.5

R300 Firmware Program : Free

• Corrected wrong messages in Italian display menu.
• Corrected garbled messages in Chinese(Traditional) display menu.

• Fixed is a symptom that absence and anomaly of visible image happens occasionally when booted.

G120/G100 Firmware Program：Free

1. 1. Thermal image quality improvement. Correction to temperature inconsistency of saved images (that could happen only occasionally).
2. 2. Fix SD card memory problem that might happen only with USB1.1 standard.

• The phenomenon of hang-up occurrence during warm up massage with execution of auto focus is corrected.

• The phenomenon of frame omission occurrence during 10Hz movie mode recording is corrected.

• If you　turn on the color alarm from OFF state and display thermal image which is saved during ON state of color-alarm, failure of abnormal thermal image phenomenon is corrected.
• During zoom ON with RUN state, if you display thermal image and switch to visual image, failure of left-right reversal image phenomenon is corrected.

• After movie is recorded in movie mode, panorama mode is turned on, failure of still running sampling phenomenon is corrected.
• After movie is saved in movie mode, failure of no-display phenomenon in thumbnail view is corrected.
• If sense is not setup while movie file is being displayed in NS9500, failure display phenomenon is corrected.
• After thermal image in panorama mode is saved, failure of disable panorama image phenomenon is corrected.

H2640 Firmware Program：Free

• Corrected a failure that values of Level and Sense sometimes do not become optimal when Full Auto function (focus, level & sense) was executed.
• Corrected a failure that reverse image function did not become effective under specific set conditions.
• Corrected a failure that, at Range-interlocking mode, temperature range is not changed to proper one when Auto Level & Sense function was executed.
• Corrected a failure that the Unit keeps alarming when it is in specific the condition of "RUN MODE".

F30 Firmware Program：Free

• Functions related to Folder (Folder Creation, Selection, Name Change and Deletion) were added.
• Loop on the menu (Iteration from top to bottom) was added.
• A problem of indicating unusual temperature, that occurs when starting from Play mode and opening thermal images without mode change, was corrected.
• A problem that temperature scale (top and bottom end) becomes same as played thermal image, that occurs when changing from Play mode with thermal image opened to thermal image mode, was corrected.

• Function of adjusting the visual image position was improved.
• Some wordings were changed/corrected in German, Chinese (traditional & simplified) and Korean menus.
• On the battery indicator, the battery remaining ranges corresponding to each level 0-3 were changed.
• Failure of noises on visual image was corrected.
• It displays thermal image when a rotary switch is on incorrect position.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.
NOTE:
If your F30 is version 1.0B or older, it has to be upgraded at our factory.
Please contact your local distributor.

TH9260 Firmware Program：Free

• Corrected a failure that values of Level and Sense sometimes do not become optimal when Full Auto function (focus, level & sense) was executed.
• Corrected a failure that, at Range-interlocking mode, temperature range is not changed to proper one when Auto Level & Sense function was executed.
• Corrected a failure that the Unit keeps alarming when it is in specific the condition of "RUN MODE".

• Corrected infrequent problem that cameras resets or freezes after long-time continuous use.
• Fixed problem of camera freeze that sometimes happens if the LCD is opened/closed while the Stand-by mode is cancelled.
• Fixed infrequent problem of not saving visible images properly.
• Corrected problem that some setting conditions cause failure in updating multi-point temperature display.
• Added a function of color bar display on thermal image at S-Video output.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

TH9100MR/WR Firmware Program：Free

• There was a malfunction, which was reported during auto focus-use on TH9100, the firmware potentially make erroneous behaves and then the unit cannot startup afterward. By updating this firmware, this malfunction is corrected.

• Corrected problem that saved visual image become in Red.
• Corrected problem of TH9100 series that the Unit keeps alarming when it is in specific the condition of "RUN MODE".

• Languages newly added on Menu: Danish, Norwegian, Finnish, Dutch and Swedish.
• Corrected infrequent problem of TH9100 series that same visual image is saved when obtaining series of visual images.
• Corrected problem that key control becomes invalid and display gets frozen when pressing ‘C’ key under certain conditions.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

TH9100MRI/WRI Firmware Program：Free

• There was a malfunction, which was reported during auto focus-use on TH9100, the firmware potentially make erroneous behaves and then the unit cannot startup afterward. By updating this firmware, this malfunction is corrected.

• Corrected problem that saved visual image become in Red.
• Corrected problem of TH9100 series that the Unit keeps alarming when it is in specific the condition of "RUN MODE".

• Languages newly added on Menu: Danish, Norwegian, Finnish, Dutch and Swedish.
• Corrected infrequent problem of TH9100 series that same visual image is saved when obtaining series of visual images.
• Corrected problem that key control becomes invalid and display gets frozen when pressing ‘C’ key under certain conditions.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

TH9100PMV/PWV Firmware Program : Free

• There was a malfunction, which was reported during auto focus-use on TH9100, the firmware potentially make erroneous behaves and then the unit cannot startup afterward. By updating this firmware, this malfunction is corrected.

• Corrected problem that saved visual image become in Red.
• Corrected problem of TH9100 series that the Unit keeps alarming when it is in specific the condition of "RUN MODE".

• Languages newly added on Menu: Danish, Norwegian, Finnish, Dutch and Swedish.
• Corrected infrequent problem of TH9100 series that same visual image is saved when obtaining series of visual images.
• Corrected problem that key control becomes invalid and display gets frozen when pressing ‘C’ key under certain conditions.

• Multi-Focus display function added.
  (The function which performs edge detection of acquired images, while moving the focus, and fuses them into an image with deeper depth of field.)
• Filtering function added.
  (Sharpness filter and Median filter)

• Added the Composite Image display funciton,when attaching an x2 Telephoto Lens, model TH91-384(Option).* is attached to the camera.
  *Note: this function is not available for x2 telephoto lens model TH91-382 (Option.)
• Uniformed the time-unit to “min" in NUC-interval setting and Auto standby-interval setting.
• Corrected the fault of the disappearance of setting menu partly due to the elimination setting (ON/OFF) of COLOR BAR, STATUS BAR and ALL, under the Japanese, Traditional Chinese, Simplified Chinese, and Korean language menu environment.

• New MENU operation added.
• New SELECT operation added.
• Users can select above new operation (Standard) or original operation (Classic).
• Focusing Point Finder added. The focusing gauge appears during auto-focusing.
• Users can check the firmware version from menu.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

***Cautions:
If you upgrade the firmware from version 5.3C (or earlier) to 5.4F (or later), the menu operation will be changed. CLICK HERE and request an instructions manual for TH9100 Series Operation Manual.

TH9100PMVI/PWVI Firmware Program : Free

• There was a malfunction, which was reported during auto focus-use on TH9100, the firmware potentially make erroneous behaves and then the unit cannot startup afterward. By updating this firmware, this malfunction is corrected.

• Corrected problem that saved visual image become in Red.
• Corrected problem of TH9100 series that the Unit keeps alarming when it is in specific the condition of "RUN MODE".

• Languages newly added on Menu: Danish, Norwegian, Finnish, Dutch and Swedish.
• Corrected infrequent problem of TH9100 series that same visual image is saved when obtaining series of visual images.
• Corrected problem that key control becomes invalid and display gets frozen when pressing ‘C’ key under certain conditions.

• Multi-Focus display function added.
  (The function which performs edge detection of acquired images, while moving the focus, and fuses them into an image with deeper depth of field.)
• Filtering function added.
  (Sharpness filter and Median filter)

• Added the Composite Image display funciton,when attaching an x2 Telephoto Lens, model TH91-384(Option).* is attached to the camera.
  *Note: this function is not available for x2 telephoto lens model TH91-382 (Option.)
• Uniformed the time-unit to “min" in NUC-interval setting and Auto standby-interval setting.
• Corrected the fault of the disappearance of setting menu partly due to the elimination setting (ON/OFF) of COLOR BAR, STATUS BAR and ALL, under the Japanese, Traditional Chinese, Simplified Chinese, and Korean language menu environment.

• New MENU operation added.
• New SELECT operation added.
• Users can select above new operation (Standard) or original operation (Classic).
• Focusing Point Finder added. The focusing gauge appears during auto-focusing.
• Users can check the firmware version from menu.

• Added the Traditional Chinese, Chinese, Korean, Russian, Italian menu.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

***Cautions:
If you upgrade the firmware from version 5.3C (or earlier) to 5.4F (or later), the menu operation will be changed. CLICK HERE and request an instructions manual for TH9100 Series Operation Manual.

TH9100MV/WV Firmware Program : Free

• Uniformed the time-unit to “min" in NUC-interval setting and Auto standby-interval setting.
• Corrected the fault of the disappearance of setting menu partly due to the elimination setting (ON/OFF) of COLOR BAR, STATUS BAR and ALL, under the Japanese, Traditional Chinese, Simplified Chinese, and Korean language menu environment.

• New MENU operation added.
• New SELECT operation added.
• Users can select above new operation (Standard) or original operation (Classic).
• Focusing Point Finder added. The focusing gauge appears during auto-focusing.
• Users can check the firmware version from menu.

• Added the Traditional Chinese, Chinese, Korean, Russian, Italian menu.
• "FILE" and “REPLAY" menu accessible during “RUN" status.
• During Replay (SIT or BMP), accessible to “DIRECTRY" menu.
• Delete an image on the Thumbnail selection menu.

• After changing a range,shortening a waiting period to be stabilized.

• Corrected the interruptive transfer problem of thermal imaging data on "IR-Motion program(TH91-757)", when AUTO focus function is done during the thermal imaging data transfer(60Hz).

• Changed the color of "SHINE COLOR" palette to emphasize contrast

• Chang RS232C parameter-setting, so as to recover the trouble of disappearance of image on LCD display due to changing of RS232C setting by resetarting camera.

• Added S/N Improvement Function (Σ32, Σ64).
• Added Visual Image Interval Saving Function.
  (Only available for saving on a memory card.)
• Added Emissivity Correction in Freeze mode.
• Added External Lens Correction.
• Added Emissivity Setup Table.
• Added Fine Color Pallet.
• Added Multilingual Display (selectable from English, Portuguese, Spanish, French, German or Japanese).

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

***Cautions:
If you upgrade the firmware from version 5.3C (or earlier) to 5.4F (or later), the menu operation will be changed. CLICK HERE and request an instructions manual for TH9100 Series Operation Manual.

TH9100MVI/WVI Firmware Program : Free

• Uniformed the time-unit to “min" in NUC-interval setting and Auto standby-interval setting.
• Corrected the fault of the disappearance of setting menu partly due to the elimination setting (ON/OFF) of COLOR BAR, STATUS BAR and ALL, under the Japanese, Traditional Chinese, Simplified Chinese, and Korean language menu environment.

• New MENU operation added.
• New SELECT operation added.
• Users can select above new operation (Standard) or original operation (Classic).
• Focusing Point Finder added. The focusing gauge appears during auto-focusing.
• Users can check the firmware version from menu.

• Added the Traditional Chinese, Chinese, Korean, Russian, Italian menu.
• "FILE" and “REPLAY" menu accessible during “RUN" status.
• During Replay(SIT or BMP), accessible to “DIRECTRY" menu.
• Delete an image on the Thumbnail selection menu.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

***Cautions:
If you upgrade the firmware from version 5.3C (or earlier) to 5.4F (or later), the menu operation will be changed. CLICK HERE and request an instructions manual for TH9100 Series Operation Manual.

TH9100ML/WL Firmware Program : Free

• Adding the composite image display function.
• Uniformed the time-unit to “min" in NUC-interval setting and Auto standby-interval setting.
• Corrected the fault of the disappearance of setting menu partly due to the elimination setting (ON/OFF) of COLOR BAR, STATUS BAR and ALL, under the Japanese, Traditional Chinese, Simplified Chinese, and Korean language menu environment.

• New MENU operation added.
• New SELECT operation added.
• Users can select above new operation (Standard) or original operation (Classic).
• Focusing Point Finder added. The focusing gauge appears during auto-focusing.
• Users can check the firmware version from menu.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

TH9100MLN/WLN Firmware Program : Free

• Adding the composite image display function.
• Uniformed the time-unit to “min" in NUC-interval setting and Auto standby-interval setting.
• Corrected the fault of the disappearance of setting menu partly due to the elimination setting (ON/OFF) of COLOR BAR, STATUS BAR and ALL, under the Japanese, Traditional Chinese, Simplified Chinese, and Korean language menu environment.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

TH9100SL Firmware Program : Free

• Uniformed the time-unit to “min" in NUC-interval setting and Auto standby-interval setting.
• Corrected the fault of the disappearance of setting menu partly due to the elimination setting (ON/OFF) of COLOR BAR, STATUS BAR and ALL, under the Japanese, Traditional Chinese, Simplified Chinese, and Korean language menu environment.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

TH7800 Firmware Program : Free

The method of firmware update is different each other, depending on the serial number of your camera.
Please perform upgrade of firmware after confirming serial no.

• Corrected problem that saved visual image become in Red.

• Added the External Lens Compensation function.

• Added the Ambient Compensation function.
• Added the Background Compensation function.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

TH7700 Firmware Program : Free

The method of firmware update is different each other, depending on the serial number of your camera.
Please perform upgrade of firmware after confirming serial no.

• Corrected problem that saved visual image become in Red.

• Added the automatic temperature level and sensitivity function.
• Added the maximum or minimum temperature display function.
• Added the alarm display function.
• Added the automatic gain control or level trace function.

• Added the External Lens Compensation function.

• Added the Ambient Compensation function.
• Added the Background Compensation function.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

TH7800N Firmware Program : Free

• Corrected problem that saved visual image become in Red.

• Added the External Lens Compensation function.

• Added the Ambient Compensation function.
• Added the Background Compensation function.

***About Instructions Manual:
If you need an instructions manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

TH7716 Firmware Program : Free

• Added the automatic temperature level and sensitivity function.
• Added the maximum or minimum temperature display function.
• Added the alarm display function.
• Added the automatic gain control or level trace function.

***About Instructions Manual:
If you need an instruction manual, CLICK HERE and send us a request form. You will be required to enter model number and serial number of your product. Please check them in advance.

TH7102MV/WV Firmware Program : Free

• Error on max/min temperature display, that displays UNDER at Max setup and OVER at Min setup, when the image mode is FAST and frame rate is 60Hz.

***About Instructions Manual:
How to Obtain Additional Function Instruction Manual To obtain the Additional Function
Instruction Manual, send the following order form to NEC San-ei Instruments, Ltd. The manual will be sent via e-mail after confirmation of the model and serial number.
TH series Additional Function Instruction Manual Order Form

TH7102MX/WX Firmware Program : Free

• Error on max/min temperature display, that displays UNDER at Max setup and OVER at Min setup, when the image mode is FAST and frame rate is 60Hz.

***About Instructions Manual:
How to Obtain Additional Function Instruction Manual To obtain the Additional Function
Instruction Manual, send the following order form to NEC San-ei Instruments, Ltd. The manual will be sent via e-mail after confirmation of the model and serial number.
TH series Additional Function Instruction Manual Order Form

Infrared Thermal Imager IEEE1394 Driver Program : Free